CMC
Electric Hydraulic Power Tilt And Trim PT-130 with Gauge - CMC
Price: $1,227.04
Save: $42.95
(3% Off $1,269.99)
Part # 13001
SHIPS TOMORROW!* if ordered in 22 hrs 46 mins.
This item is found in the following Product Families
PT-130 Rated for 130 hp and smaller motors, the 13002 will trim the motor 20° and a total of 65° of trim and tilt. It is actuated with a totally waterproof marine electric hydraulic system that is rated over 7800 lbs. of thrust! This hydraulic system is made of 100% non-ferrous materials which makes it more impervious to saltwater and freshwater than ball screw, electro-mechanical systems equipped on other brands. In fact, it is over twice as powerful as the ball screw electro mechanical actuator. The CMC hydraulic system is completely sealed and submersible and runs without worry of water damage. It is constructed of 1/2" 6061 T6 alloy aluminum extrusions and fastened with stainless steel fasteners for maximum strength and durability. No welds or castings to break. Carry's a 5-year structure warranty. Unit incorporates a 6" set back which enhances boat stability and will put the prop in "cleaner" water, thus giving the prop a better "bite" and eliminating prop slippage. It can also increase top end speed and fuel efficiency. It is great for pontoon boats, too! Since access to the motor on most pontoon boats is very difficult, the 13002 can make it very convenient. It is back saving, and prop saving, simply by flicking a switch when approaching shallow water. Note: clamp-on motors need an adapter (13022).PT-130 FEATURES:
  • Rated for 130 H.P. and Smaller Motors
  • 6" Set Back to Enhance Boat Stability and Performance
  • 20° of Trim and a Total of 90° of Tilt and Trim
  • Product weight: 40 lbs.
  • 1/2" 6061 T6 Extruded Aluminum Construction with Stainless Steel Fasteners
  • Electric Hydraulic Actuator Rated at 7853 lbs. of Thrust!
  • Standard B.I.A. Bolt Hole Pattern
  • Convenient Adapter Kit Available for Clamp-on Motors
  • Four Stainless Steel Motor Mounting Bolts Included
Full StarFull StarFull StarFull StarFull Star
Based On 4 Reviews | Write Review
Full StarFull StarFull StarFull StarFull Star
Wonderful Product
by Pamela from Cheyenne, Wyoming on May 24, 2015
This is a great product. It installed easily and works well.
(4 of 5 people found this review helpful)
Was this review helpful?
Full StarFull StarFull StarFull StarFull Star
Fit great and works great!
by Doug from Logan, Ohio on May 19, 2015
Works as described love it
(4 of 4 people found this review helpful)
Was this review helpful?
Full StarFull StarFull StarFull StarEmpty Star
received CMC power tilt trim unit
by Patrick from Peterborough, Ontario on June 18, 2012
I have not installed the unit yet, but it is everything I expected and should do the job for me. Thanks
(5 of 8 people found this review helpful)
Was this review helpful?
Full StarFull StarFull StarFull StarFull Star
BEST BANG FOR THE BUCK
by Scott from bradenton, Florida on June 03, 2010
Have a 90 hores on a 17ft boat that did not have tt . dealer wanted three times the amount just for parts. the cmc unit is so eazy to install. it took me about one hr to install by myself. every nut and bolt thats needed was there. I have had this on my boat now for about 3 and half years and use the boat atleast 2 times a week."thank god for the weather in fl." and it looks and works just the same today as it did the dad i took it out of the box!! in fact my budy has the same boat and yr. that came with tt and the cmc is twice as fast. and is a real back saver at the end have the day when u dont have to tilt by hand....
(47 of 48 people found this review helpful)
Was this review helpful?
Q:
How much does these weigh?
A:
This product weighs approximately 40 lbs.


Q:
I have a 20hp tohatsu 4 stroke, will the PT 35 work and adapt to my current motor or will I need an adaptor.?
A:
No need for an adaptor, should mount with the industry standard BIA pattern.


Q:
Can this be wired into the tilt and trim button on my control handle?
A:
This can be wired to your tilt and trim button on your control handle as long as you have a 3 wire switch.


Q:
What models does this work for? Johnson? 1977 85HP?
A:
This will work for any engine between 65 and 130 horsepower.


Q:
I do a lot of towing with my 17 ft 1987 Sea Nymp with 50 hp Mariner. Will this unit put extra stress on the transom due to the extension from the transom especially when tilted during towing?
A:
It is entirely possible. For more information in this area, feel free to call us at (800)-914-1123.


Q:
Can anyone verify that this unit WILL NOT automatically lower when power is applied to the throttle. My current Mercury has a "safety feature" that lowers the tilt to the upper trim limit @ anything over 1500 rpm. It's not a powered lowering, just a pressure release within the cylinder.t"?
A:
CMC confirms that this will not automatically lower when power is applied to the throttle.


Q:
Does this unit have the trim buttons to place on throttle control handle. or mounting box etc ?
A:
CMC confirms you can wire the 3 wires into any 3 terminal switch. So as long as your switch in the throttle is 3 terminals, it will work.


Q:
Will this hold up a mariner 115 hp and hold trim on pontoon 21'?
A:
Yes it will hold your motor. It holds up to 130 HP engines.


Q:
Will this work on a 1986 50hp mercury?
A:
Yes this will work as it takes standard B.I.A bolt hole patterns.


Q:
I have an older 55 hp application for the restoration of an older run-about glass boat. It is built for a short shafted motor install. I have a great long shafted 55 HP Johnson that I would to use instead. Does the PT 130 come with multiple B.I.A patterns that will allow this transformer, and is there a web site place that I can research your multiple bolt patterns to be more certain that I can bolt this long shaft motor to this short shaft boat before I buy one only to find out I have no chance that it will work? My e-mail address is larcher@neo.rr.com?
A:
It only comes with the standard BIA pattern which has been in effect for many years. So it only comes in one. We can send the specs of the BIA hole pattern, but you you will need to contact us at the number at the top of the page.


Q:
Will this work with a mercury 9.9 4st bigfoot?
A:
The PT-35 would be a better fit as it is made for smaller outboards up to 35 HP. http://www.iboats.com/Electric-Hydraulic-Power-Tilt-And-Trim-PT-35-CMC/dm/view_id.392343


Ask a question
Question & Answer Guidelines
This product ships in 1 business day.
Add to Cart and enter your Postal Code to determine the shipping charges.
Most products and orders leave our warehouse in 1 business day. However, select items may take more processing time. Alaska and Hawaii orders please add 1 additional warehouse processing day.
Standard Shipping Policies