This product has been discontinued.
Mallory
Mallory Carb Kit 9-37501
Price: $24.99
Discontinued
Save: $4.48
(15% Off $29.47)
Part # 9-37501
(Discontinued)
This item is found in the following Product Families
Replaces Original Equipment Manufacturer(OEM):Yamaha
Replaces Original Equipment Manufacturer # (OEM #):6H1-W0093-01
Fits Application:75-90

Includes parts to repair 3 carburetors.

Average Customer Review for Mallory Carb Kit 9-37501
Full StarFull StarEmpty StarEmpty StarEmpty Star
Based On 9 Reviews | Write Review
Full StarFull StarFull StarEmpty StarEmpty Star
mallory carb rebuild kit for 85 h.p. yamaha 2 stroke
by Danny from Berryville, Arkansas on March 16, 2016
The kit had all the parts and they worked fine EXCEPT for the floats. They were thicker (viewed from the side) and would not swing up and down to lift the jet. When you put the screw down to tighten the pin, it just locked the float up. Had to put the old floats back in.
(1 of 2 people found this review helpful)
Was this review helpful?
Full StarFull StarFull StarFull StarFull Star
Good deal check here first.
by Melvin from Cape Coral, Florida on March 05, 2016
i got 3 rebuild kits for just a bit more than one at another site...
Was this review helpful?
Full StarFull StarEmpty StarEmpty StarEmpty Star
floats don't fit
by Michael from Brighton, Colorado on August 24, 2015
I was only able to use parts of the kit. The floats did not fit correctly and hit the fuel pickup tube in the bowl. Gaskets worked fine.
Was this review helpful?
Full StarFull StarFull StarFull StarEmpty Star
carb overhaul
by Leroy from Mabank, Texas on April 08, 2015
everthing worked fine except the floats, Ther were not the same as the ones in the carbs bur no problem. used the old ones
Was this review helpful?
Full StarEmpty StarEmpty StarEmpty StarEmpty Star
You get what you pay for...
by Wendy from New Ellenton, South Carolina on August 19, 2014
This product is just plain junk. The o'ring type gaskets did not fit. The float valve were too short and could not seat seat causing the carbs to flood. The floats themselves would not fit. The jets were longer than the originals although you could get them to work. So in short, this kit is the price of one good kit, but you cannot make one good kit from all of it.
(0 of 1 people found this review helpful)
Was this review helpful?
Full StarEmpty StarEmpty StarEmpty StarEmpty Star
does not fit
by Murray from Hartford, Kentucky on July 29, 2014
this kit does not fit this carb.
Was this review helpful?
Full StarEmpty StarEmpty StarEmpty StarEmpty Star
Mismatch of Parts
by Richard from Dallas, Texas on August 13, 2013
Most of the pieces on this carb fit do not fit and using only a few of the pieces does not work well as you have to adjust the other pieces. I was able to use the float but it's matched to the float bowls which don't fit. I had to modify my existing float bowls. So basically I used 3 parts of this entire kit. DO NOT ORDER THIS UNLESS YOU PLAN AND THROWING AWAY OVER HALF THE PIECES (AND HOPE THE ONES YOU ARE THROWING AWAY ARE THE ONES YOU DIDN'T NEED)!!! I already had the carbs removed so I used what I could to get the engine running again.
Was this review helpful?
Full StarEmpty StarEmpty StarEmpty StarEmpty Star
parts do not fit.
by Peter from Cape Coral, Florida on April 12, 2012
The float bowls are not the right shape and the gaskits are not the right and do not match up. I need to return these kits. Thanks, Pete
(2 of 5 people found this review helpful)
Was this review helpful?
Full StarEmpty StarEmpty StarEmpty StarEmpty Star
Won't on yamaha C85 or any carb from what I can Tell
by Alan from Albany, Georgia on April 03, 2011
Just to look at it,It looks like all the correct parts for a Yamaha C85 Carb. The First thing was the float height was a little low in the closed position and did not drop low enough in the open position. Tried using the old float and it was now worse.(That should have a red flag) I modified (sanded)the stops on the back of the new float so it would open properly and ignored the slight difference in the closed height. Assembled and All the carbs flooded! I couldn't believe the slight difference in the float height(1/64in) allowed this to happen. Took it back apart and looked real close to find the needle valve keeper/spring was touching the needle valve seat preventing from closing all the way. So I say this would not work on any carb. It appears the hole in the valve seat is too low or drilled out too far or the wrong one all together.
(1 of 3 people found this review helpful)
Was this review helpful?
Q:
Will this kit fit a Tohatsu M55B?
A:
No.


Ask a question
Question & Answer Guidelines
This product ships in 1 business day.
Add to Cart and enter your Postal Code to determine the shipping charges.
Most products and orders leave our warehouse in 1 business day. However, select items may take more processing time. Alaska and Hawaii orders please add 1 additional warehouse processing day.
Standard Shipping Policies