Boat Cover Support System

Doesn't fit my 23' deck boat as well as expected. I had to remove the walk-through windshield section to have room for the post. I added a second post aft of it for a vent so I think it will work OK.

The front strap was not long enough on my 23' deck boat and I had to remove my pass through windshield for the post but I added a second post for a vent so it worked well in the end.

The boat cover support system is easy to set up. Looks like cover is supported well. Just put it to use, so hoping it does the job well.

Pole and straps work perfect. The systems keeps cover up so rain water runs off with no puddles.

The structure works well to keep rain flowing off the cover, however the button connection between the pole and the reinforced fabric broke within the first few uses. The pole will still stay under the fabric but the fastener is useless.

Very Easy to use. I suggest a Velcro strap for storing the lengths of straps when not in use to prevent tangles and snagging when not in use.

I will be returning this with the cover due to poor fit.

This is a replacement item, had one before, works great.

The reinforced areas for the mirrors and the Aft corners do not line up/cover where they are intended to.

Not s y enough to keep rain from pooling in cover. The straps were not long enough for my 24ft. pontoon, rigged it with archer strap still wasn't s y.

Used this system for about 10 years. 1" webbing finally deteriorated, so ordered another complete set, including pole. Bow strap is around 10 to 15 feet shorter than the original. Had to add another piece of 1" webbing to make the connection. The two stern cleat straps are definitely longer that the original. Thinking strap needed for bow went to stern connections. New support pole has better telescope latch - a screw. Original used a friction clamp, which wore out in a year. I use another style pole at the bow to assist with water run off, since my 20 ft boat has a high bow rail. Still like the system, overall.

We use this on a little 17' 6" Sea Ray, and it works as advertised. That said, the plastic buckles seem a little weak. We'll see if they stand the test of time.

Works great easy to install.

This products does not fit the boat that is it was advertised to fit.

The stapes make the cover stay tight and doesn't allow any puddling when it rains

This support looks taller on the website than it is. This support is not tall enough to improve rain runoff for Four Winns Sundowner.

even tried taping straps to keep them from slipping, no luck. Its a POS.

Easy to install, works good

The straps slip even when put on according to directions, then water pools on cover then it leaks into the boat. In the back where the pole is seems to work. The front is a disaster. It seems there should be some additional clips of some kind to keep the straps tight. We have put a second pole on the from and are trying that.

Great fit, nice color.

It works pretty good .

Not as robust as I thought it would be. Should be ok for rain, when the snow kicks in it will need a little help.

This is great, easy to install and meets the challanges of keeping water from collecting.

Everything seems to be what advertised. At the end of winter we will see.

Product for a 16' boat does not have enough secondary support to hold the boat cover securely. If a foot of wet snow sat on this system I feel it wouldn't hold.

Takes a little time to get it set up right, but it keeps the sag out of the cover so you do not get the puddles from sagging.

Called Taylor to exchange cover. I think I ordered the wrong cover, my boat has a swim platform and I didi not add that in when ordering. Taylor was very helpful with ordering another cover.

I have a 21 hews redfisher it would not cover 3/4 of my boat I have a poling platform it came with a poling platform cover of=rdered it with I returned it denny

I am very pleased with this support system. Before using it, my cover would sag down and collect a ton of rain. With this, the rain just runs off with no problem.

came on time and product as advertised

Just what I needed to make my current cover work. Great product

We're very happy with the new boat cover for the most part. The one thing we don't understand is the cutout for the motors. We're finding that whether the motor is raised up or down it is difficult to fit the cover around it. We ordered the cover to fit an outboard, can it possibly be meant for an inboard?

Have a hard time keeping the snap on while putting the support system on the boat.